This update contains the following changes and improvements:

◉ SSTV: Robot 36 pictures (the mode the ISS sends) came out green and only showed their left half; fixed, together with other modes that were slanted or shifted sideways

◉ SSTV: pictures start in the right place by themselves, and the start of a picture is recognised with weaker signals and when the receiver is tuned up to 100 Hz off

◉ SSTV: every mode can now be sent, including Robot 36, Robot 72, Robot 24 and PD-50 to PD-290

◉ SSTV: the sender's call sign (FSK ID) is shown again

◉ Antenna Genius: the antenna buttons work again with firmware 4.1.9; a tap selects the receive antenna, while transmitting the transmit antenna

◉ Power Genius XL: changing the remote access code works; Rotator Genius: rotator names are saved correctly

◉ PSK Reporter: changing the time, band or mode in the filter now loads the list again

◉ Network Stats: a Saved Radios section shows whether each of your saved radios answers, also while not connected

◉ Radio list: a dot before each radio shows whether it answers, and its address is shown below the name

◉ Waterfall: Center, the level slider and the zoom buttons moved to the left

◉ Implemented several additional improvements and optimizations behind the scenes


Kindly use the ‘CONTACT SUPPORT’ feature under Settings of the app in case of questions or issues. I will ensure your request is promptly answered or resolved.

Your continued support and valuable feedback play a crucial role in further improving this app.

73s,

Marcus, DL8MRE

This update contains the following changes and improvements:

◉ A new look: the app now follows Apple's own iOS design, in light and dark mode, on the iPad and the iPhone

◉ New tab bar with Waterfall (iPhone: VFO), Modes, Tools, your radio and Settings

◉ Modes and tools keep running when you leave their screen; a green dot on the tile shows which ones are running

◉ Runs on Apple Vision Pro

◉ New modes: FT8-Improved and JS8 (iOS 26), Speech (iOS 26: incoming voice transcribed and optionally translated, your typed text sent as speech) and CW with decoder and CW keyboard

◉ CW: improved decoder

◉ CW: the new ESM mode (Enter Sends Message)

◉ HF-Fax and SSTV: a frequency list that tunes the radio, and Auto Save into Photos

◉ All tools redesigned: DX Cluster, POTA, PSK Reporter, Band Plan, Call Lookup, Logbook, Network Stats, Memories, Scanning, FS2M Keyer, Command Bar, Ultra Beam and the controllers

◉ New: Genius (4O3A) devices

◉ Voice Macros: the radio's voice memories or your own recordings in the app

◉ Several MIDI controllers can be used at the same time

◉ The radio controls are now compact floating panels (CW, Memories, Tune Stack, Macros, Command Bar, DTMF, RIT / ∆TX, D-Star)

◉ The Tuning panel and the PTT are floating panels too

◉ The band plan is shown on the waterfall as a coloured ribbon

◉ Demo radio: try the app without a radio

◉ The radio keeps playing in the background, for example with the iPad cover closed or the screen locked

◉ Fixed: the audio didn't come back after a phone call or after an interruption by another app

◉ Fixed: a crash when iOS started the app in the background

◉ New controller actions: VFO / Memory Toggle, VFO Mode, Memory Mode, Mode Previous, CW pitch, Clear Log Window, Memory 1-10, Memory Up / Down

◉ Controller knobs on RIT change it in 10 Hz steps from the current offset

◉ IC-7300 / IC-7300MK2 offer Preamp 1 and 2 only; IC-705 Preamp 1 and 2, IC-9700 and IC-905 Preamp 1

◉ IC-7300 / IC-7300 MK2: A / B now exchanges the two VFOs (before, the radio only switched to VFO B)

◉ FT8 and JS8 only widen a filter narrower than 3 kHz and no longer make a wider one narrower

◉ WSPR: received spots reach WSPRnet again; the status line shows the result

◉ Restore default settings keeps your calls, macros, Command Bar, logins and radio list

◉ The Dark Mode setting works again (default: Auto)

◉ Better VoiceOver support

◉ The manual has been updated

◉ Implemented several additional improvements and optimizations behind the scenes


Kindly use the ‘CONTACT SUPPORT’ feature under Settings of the app in case of questions or issues. I will ensure your request is promptly answered or resolved.

Your continued support and valuable feedback play a crucial role in further improving this app.

73s,

Marcus, DL8MRE

This update contains the following changes and improvements:

◉ Added a Terminal mode for APRS. You can now connect to BBSes or start a keyboard-to-keyboard session with another ham radio operator.

◉ APRS can now auto-repeat position and status reports.

◉ The APRS RX button now indicates a transmission, providing clearer feedback.

◉ Additional APRS improvements and refinements.

◉ For the RIT/XIT view there is now a setting for defining minimum and maximum RIT/XIT values, improving support for satellite operation.

◉ Command Bar improvements.

◉ PTT Double-Tap has been removed for a better PTT button experience.

◉ The “Available Radios” screen now remembers the last connection so you can just hit the Connect button in case you like to connect with the same Radio.

◉ Additional changes in preparation for an upcoming iOS release.

◉ Implemented some additional improvements and optimizations behind the scenes


Kindly use the ‘CONTACT SUPPORT’ feature under Settings of the app in case of questions or issues. I will ensure your request is promptly answered or resolved.

Your continued support and valuable feedback play a crucial role in further improving this app.

73s,

Marcus, DL8MRE

This update contains the following changes and improvements:

◉ Added support for the HaliKey MIDI Keyer USB Controller

◉ Added an additional Azimuth Offset Setting the for Metropwr RT1 Rotator Controller

◉ A warning will now be displayed when the Low Data Mode is enabled

◉ An issue in the POTA Tool when showing a map was fixed

◉ Added Frequencies for 2200m, 630m and 23cm to the WSPR Tool

◉ Improved logbook iCloud handling in case of poor internet access

◉ Logbook export will now also export even wrong or incomplete QSOs

◉ Implemented some additional improvements and optimizations behind the scenes


Kindly use the ‘CONTACT SUPPORT’ feature under Settings of the app in case of questions or issues. I will ensure your request is promptly answered or resolved.

Your continued support and valuable feedback play a crucial role in further improving this app.

73s,

Marcus, DL8MRE

This update contains the following changes and improvements:

◉ Fixed an issue when using the Call lookup from inside certain tools

◉ Fixed an issue when changing Memory Groups in Memory Mode

◉ Implemented some additional improvements and optimizations behind the scenes


Kindly use the ‘CONTACT SUPPORT’ feature under Settings of the app in case of questions or issues. I will ensure your request is promptly answered or resolved.

Your continued support and valuable feedback play a crucial role in further improving this app.

73s,

Marcus, DL8MRE